Mts Sensor MHRM Mobile Hydraulic Position Sensor

Mts Sensor MHRM Mobile Hydraulic Position Sensor

Product Name: Mts Sensor MHRM Mobile Hydraulic Position Sensor
Product Brand: Mts Sensor
Product Code: MHRM
Product Artikel: Mts Sensor MHRM Mobile Hydraulic Position Sensor
Output Signal characteristic Analog output restricted by noise or A/D converter of control unit Voltage 0.25…4.75 VDC; 0.5…4.5 VDC; 0.25…9.75 VDC; 4.75…0.25 VDC; 4.5…0.5 VDC; 9.75…0.25 VDC Current 4…20 mA; 20…4 mA Measured value Position Measurement parameters Resolution ±0.1 mm typical Linearity 0050…0250 mm 0255…2000 mm 2005…2500 mm ≤ ±0.1 mm ±0.04 % (F.S.) ≤ ±0.8 mm Hysteresis ≤ ±0.2 mm Setpoint tolerance ±2 mm Operating conditions Operating temperature −40…+105 °C Storage temperature −25…+65 °C Humidity 90 % relative humidity, no condensation Ingress protection – M12 connector IP67 / IP69K (correctly fitted) Ingress protection – Sensor housing IP67 Shock test (according to EN 50155) According to EN 61373 Cat2 (Bogie) and Cat3 (Axle) Vibration test (according to EN 50155) According to IEC 60068-2-64-Fn Cat3 (Axle) EMC test (according to EN 50155) EN 50121-3-2 ISO 14982 Agricultural and forest machines EN 13309 Construction machines ISO 16750-2 Electromagnetic immunity according to EN 61000-6-2 Electromagnetic emission according to EN 61000-6-3 RF immunity 200 V/m per ISO 11452-2/-4 PCB coating According to EN 50155 Pressure (according to DIN EN ISO 19879)* Ø 7 mm sensor rod Ø 10 mm sensor rod PN (nominal operating) 300 bar 350 bar Pmax (max. overload) 400 bar 450 bar Pstatic (proof pressure) 525 bar 625 bar Design / Material Housing lid Compound PBT (glass fiber reinforced plastic); sealing ring: TPU Sealing O-ring NBR with back-up ring PTFE Sensor electronics housing Stainless steel 1.4305 (AISI 303) Sensor rod – Ø 7 mm Stainless steel 1.4301 (AISI 304) Sensor rod – Ø 10 mm Stainless steel 1.4306 (AISI 304L) Stroke length 50…2500 mm Mechanical mounting Mounting instruction Please consult the technical drawings Mounting position Any Electrical installation Connector InterConnection plug Operating voltage 12 / 24 VDC (8…32 VDC) 24 VDC supply 12 VDC supply Load (output mA) RL  ≤ 500 Ω RL  ≤ 250 Ω Load (output VDC) RL  ≥ 10 kΩ RL  ≥ 10 kΩ Inrush current 4.5 A / 2 ms 2.5 A / 2 ms Operating voltage ripple 1 %PP Power drain ≤ 1 W Over voltage protection (VDC-GND) Up to +36 VDC Polarity protection (GND-VDC) Up to −36 VDC Insulation resistance R ≥ 10 MΩ @ 60 sec according to EN 50155 Dielectric strength 708 VDC (DC ground to machine ground) according to EN 50155 MHRM EMBEDDED – TECHNICAL DATA */ According to calculations under use of the FKM guideline Cycles Ø 7 mm sensor rod Ø 10 mm sensor rod Dynamic pressure: < 2 × 106  pressure cycles 300 bar 350 bar Static pressure: < 2 × 104A  pressure cycles 400 bar 450 bar Proof pressure: Maximum 5 minutes testing time for cylinder pressure test 525 bar 625 bar