Mts Sensor MH SIL2 Mobile Hydraulic Position Sensor

Mts Sensor MH SIL2 Mobile Hydraulic Position Sensor

Product Name: Mts Sensor MH SIL2 Mobile Hydraulic Position Sensor
Product Brand: Mts Sensor
Product Code: MH SIL2
Product Artikel: Mts Sensor MH SIL2 Mobile Hydraulic Position Sensor
Output Signal characteristic Continuously analog output restricted by noise or A/D converter of control unit Voltage 0.5…4.5 VDC with failure signal < 0.5 VDC LO > 4.5 VDC HI Current 4…20 mA with failure signal < 4.0 mA LO > 20 mA HI Measured value Position Measurement parameters Resolution Typ. 0.1 mm Power uptime Typ. 250 ms Linearity 0050…0250 mm 0255…2000 mm 2005…2500 mm ≤ ±0.1 mm ±0.04 % (F.S.) ≤ ±0.8 mm Hysteresis ±0.1 mm Internal sample rate 1 ms Setpoint tolerance ≤ 1 mm Operating conditions Operating temperature electronics −40…+100 °C Storage temperature −20…+65 °C Fluid temperature −30…+85 °C Humidity EN 60068-2-30, 90 % rel. humidity, no condensation Ingress protection – M12 connector EN 60529 – IP69K (correctly fitted) Ingress protection – Sensor housing EN 60529 – IP67 Shock test IEC 60068-2-27, 100 g (6 ms) single shock, 50 g (11 ms) at 1000 shocks per axis Vibration test IEC 60068-2-64, 20 g (r.m.s.) Ø 10 mm pressure pipe (10…2000 Hz) – resonance frequencies excluded EMC test UNECE Regulation 10 Rev 5: Electromagnetic Compatibility ISO 14982 Agricultural and forest machines EN 13309 Construction machines Immunity: ISO 11452-2 (200 V/m Antenna), ISO 11452-4 (200 mA BCI) Emissions: CISPR 25 Transiente Impulses: ISO 7637-1/2 E.S.D.: ISO/TR 10605 The sensor meets the requirements of the EC directives and is marked with Pressure (according to DIN EN ISO 19879)* Ø 10 mm pressure pipe PN (nominal operating) 350 bar Pmax (max. overload) 450 bar Pstatic (proof pressure) 625 bar Design / Material Sensor electronics housing Stainless steel 1.4305 (AISI 303) Sealing O-ring 40.87 × 3.53 mm NBR 80, back-up ring 42.6 × 48 × 1.4 PTFE Sensor rod Stainless steel 1.4306 (AISI 304L) M12 connector insert Material: polyamide reinforces; O-ring 7 × 1.35 mm NBR 70; pins: brass with gold plated pins M12 flange Brass nickel-plated with O-ring 13 × 1.6 NBR 70 Stroke length 50…2500 mm Mechanical mounting Mounting position Any Mounting instruction Please consult the technical drawings Electrical installation Connector M12 male connector Supply voltage 12 VDC (8…32 VDC) 24 VDC (16…32 VDC) Current consumption Typ. < 100 mA Typ. < 50 mA Load (output VDC) RL  > 10 kΩ RL > 10 kΩ Load current (output VDC) Typ. 0.5 mA Typ. 0.5 mA Load (output mA) RL  < 250 Ω RL  < 500 Ω Inrush current Max. 2.5 A/2 ms Max. 4.5 A / 2 ms Supply voltage ripple < 1 % PP Power drain < 1 W Over voltage protection (GND - VDC) Up to +36 VDC Polarity protection (GND - VDC) Up to −36 VDC Insulation Resistance R ≥ 10 MΩ @ 60 sec Electric strength 500 VDC (DC GND to chassis GND) */ According to calculations under use of the FKM guideline Cycles Ø 10 mm sensor rod Dynamic pressure: < 2 × 106  pressure cycles 350 bar Static pressure: < 2 × 104  pressure cycles 450 bar Proof pressure: Maximum 5 minutes testing time for cylinder pressure test 625 bar